Calibration and certification
Your Prolaser 3 must be checked every year.
Calibration and certification
Your Prolaser 3 must be checked every year.
Have the annual calibration of your ProLaser 4 or ProLaser 3 laser speed gun carried out during one of our monthly sessions.
We arrange for your device to be collected, prepared before inspection, shipped to us, tested, and returned to your department.
ProLaser calibration sessions are held around the 15th of each month, except in August.
We recommend contacting us about 2 months before your calibration due date.
This timeframe allows us to:
To participate in a session, your ProLaser 3 or ProLaser 4 must generally reach us during the last 10 days of the month preceding the session.
For a session scheduled around June 15, your device must reach us during the last days of May.
This organization allows us to carry out the necessary checks and preparations before inspection: sighting, alignment, general operation, and preliminary tests.
Sessions are generally held around the 15th of each month.
Please note: no calibration sessions are held in August.
To guarantee a place in your preferred session, we recommend contacting us well in advance.
Once your appointment is scheduled, we will email you the procedure for shipping your device.
You can drop off the box containing your ProLaser case at an official post office near you.
You will be provided with a Chronopost shipping label.
Around the 20th of the month preceding the session, we will provide you with:
The drop-off period is generally scheduled over about a week to ensure your device arrives on time.
To prepare your file, please provide us with:
The ProLaser serial number generally consists of 4 or 5 digits and is located on the bottom or back of the device.
Your ProLaser must be placed in its original shockproof case.
The case must contain:
The complete case must then be placed in a sturdy and properly protected box, ideally the original box.
An identification sheet must be placed inside the case with the following information:
We will provide you with the necessary information so that this document can be printed and placed with the device.
Upon receipt, your device is prepared for the scheduled session.
The various steps include pre-inspection checks and tests, the inspection, post-inspection tests, and then the preparation for the return of your device.
Your ProLaser is generally shipped back about a week after its calibration and post-inspection tests.
Please allow for approximately 3 weeks of unavailability between the collection of your device and its redelivery.
Preparation and tests → Inspection → Post-inspection tests → Reshipping
We therefore recommend that departments using their speed gun daily plan well in advance for the period during which the device will be unavailable.
This service is intended for the annual calibration of ProLaser 4 and ProLaser 3 laser speed guns.
When requesting a quote, simply indicate the device model, its serial number, and the month of your preferred session.
Would you like to book an upcoming calibration session for your ProLaser 4 or ProLaser 3?
Use the "QUOTE" button and indicate your device model, its serial number, and your preferred month for calibration.
The procedure presented here concerns the annual calibration of ProLaser 3 and ProLaser 4 devices. We recommend contacting us about two months in advance.
Sessions are generally held around the 15th of each month, except in August.
Please allow approximately 3 weeks between the collection and redelivery of the device.
The device must generally reach us during the last 10 days of the month preceding the session.
We will send you a Chronopost label and the procedure for dropping off the package at an official post office near your establishment.
The ProLaser must be sent in its original shockproof case, accompanied by its accessories, batteries or rechargeable batteries, charger, cigarette lighter adapter, and metrology logbook
We arrange the annual inspection of ProLaser 4 and ProLaser 3 laser speed guns. When submitting your request, please provide the model, serial number and due date shown on the metrology documents supplied with your device.
The annual inspection verifies the metrological performance of your device and provides the documents corresponding to the inspection performed. Planning ahead makes the service easier to organise and helps minimise downtime while the equipment is away.
We recommend contacting us approximately two months before the anniversary date of the inspection. This allows enough time to prepare the quotation, receive your approval or purchase order, reserve a session and arrange transportation.
Check the metrology logbook and documents supplied with your ProLaser 4 or ProLaser 3. If you are unsure, send us a copy of the most recent inspection document, together with the model and serial number, so that we can prepare the service.
Sessions are usually scheduled around the 15th of each month, except in August. Your device’s appointment is confirmed when the service is arranged, subject to availability.
No sessions are organised in August. If your inspection is due during this period, contact us early enough to arrange a session beforehand. Please do not wait until the last minute to reserve the service.
Collection is generally arranged during the last ten days of the month preceding the session, so that the equipment is received at the end of the month. Exact dates are agreed with you when the service is booked. Please wait for the collection instructions before sending any equipment.
An estimated turnaround time of one to two weeks is usually provided. To plan the actual period during which your device will be unavailable, ask us to confirm the collection and return dates. These depend on the selected session, transportation and any action required following the inspection.
Place the device in its protective carrying case, then pack the case inside a suitable cardboard box with sufficient protective material. Clearly identify your organisation and the equipment. Follow the instructions provided regarding the documents, accessories and power supply that must be included.
Please confirm the required contents when booking the service. The tripod, tripod head, charger and other accessories should not be included automatically unless requested. The list of required items will help you prepare a package suited to the planned service.
Report any problem when requesting the quotation: measurement difficulties, display problems, unstable power supply, impact damage or deterioration. Describe the symptoms and include photographs if necessary. An annual inspection request should not be considered as automatically including a repair.
Your ProLaser is returned with the metrology documents corresponding to the inspection performed. Keep them with the device records to maintain its history and prepare for the next due date.
For requests involving several devices, send us a list of their models, serial numbers and due dates. Please also specify your availability requirements so that we can consider a schedule suited to your department.
Provide the name of your organisation, the relevant model, its serial number, inspection due date and details of any known fault. To prepare your request, contact VIRTUAVIA:
In the comments field, specify “Annual ProLaser 4 calibration” or “Annual ProLaser 3 calibration”.